iSWAP 2: pockets and coupler

Two large pocket transmons, 8 mm apart, joined through a flux-tunable coupler (a SQUID in a bus line with two round pads). Each qubit has a 10 mm line to a launchpad, and the coupler has a flux line to a third. It is example 2 of the Qiskit Metal iSWAP-gate notebook (after Phys. Rev. Research 2, 033447, Fig. 1, structure only; Apache-2.0, © IBM and contributors). The Quantcore rebuild is distributed under GPL-3.0.

Build this one to learn how a tunable coupler sits between two qubits with a pocket of its own, and how long port lines run to the pads. The chip has no readout resonator.

The whole iswap2 chip as the v2 notebook builds it

At a glance

Notebook

examples/designs/metal/iswap2_pocket_tc.ipynb (an older one-cell version is kept as iswap2_pocket_tc.v1.ipynb)

Source

Qiskit Metal Full-Physical-Design-of-iSWAP-Gates.ipynb, example 2, © IBM and contributors, Apache-2.0

Chip

16 × 6 mm (the source’s size, larger than the 7.5 mm Quantcore die)

On the chip

2 pocket transmons (1 × 0.4 mm pads) · 1 tunable coupler with a Quantcore SQUID · 2 lines of 10 mm · 1 flux line · 3 bond pads

Builds today

yes (layout built on 2026-11-19 in 9 s)

How the notebook builds it

The layout segments of iswap2, one picture each
  1. Die. An empty 16 × 6 mm chip with the QCT frame (dicing marks, alignment grids, chip boundary, device ID).

  2. Bond pads. Three launchpads slid to the 100 µm pad-edge rule (the picture zooms on one pad).

  3. Readout. None: the two 10 mm lines end on their pads, so they are port lines.

  4. Qubits. Two mm-scale TransmonPocket6 qubits with Quantcore junctions.

  5. Lines. A 10 mm meandered line from each qubit’s outer pad to its launchpad.

  6. Coupler. The tunable coupler with its pocket and the two lines to the qubits.

  7. Flux line. The coupler’s flux bias line from the east pad.

  8. Whole chip. The sim group (both qubits and the coupler), the centring check, the design saved.

LOM estimates

Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 39 s): QuCat normal modes with QuTiP dressed values.

group

qubit

f_q (GHz)

α (MHz)

resonator

f_r (GHz)

κ (MHz)

χ (MHz)

Q1+route4

Q1

4.222

-102

–

–

–

–

Q2+route5

Q2

4.222

-102

–

–

–

–

TC

TC

5.149

-155

–

–

–

–

LOM plot of iswap2_pocket_tc

These are lumped-model estimates from component formulas and calibration, not FEM results. The LOM page says how far to trust them.

Build spec

The rest of this page is the detailed spec the notebook was built from: every component, port, route and length.

The metal: references in this spec build as written, through the metal: wrapper (ports are the Metal pin names, parameters the Metal options). The Quantcore and KQC substitutions are optional.

The notebook examples/designs/metal/iswap2_pocket_tc.ipynb builds all metal: cells (TransmonPocket6, TunableCoupler02) at the source’s scale and adds a TC02 pocket of 3.8 × 2 mm. A coupled LOM of the TC02 model (a series SQUID) is not available.

Source: Quantum Metal docs/circuit-examples/F.Small-quantum-chips/Full-Physical-Design-of-iSWAP-Gates.ipynb, Example 2, after Phys. Rev. Research 2, 033447 (2020), Fig. 1 (structure only). Licence Apache-2.0. The chip has two large TransmonPocket6 qubits, each with two pads. A TunableCoupler02 (a floating two-pad SQUID coupler with a flux-bias line) sits between them. Each qubit has a 10 mm meandered line to its own wire-bond pad, and the coupler’s flux line goes to a third pad. mm-scale: pads 1 × 0.4 mm, pocket 1.5 × 1.2 mm, pad_gap 50 µm; coupler pocket 3 × 2 mm, pad radius 0.3 mm. The chip is 16 × 6 mm centred at (0, 1) mm, so Designer = Metal + (8000, 2000). cpw_width 10 µm, gap 6 µm. A first build uses these substitutions: Xmon for TransmonPocket6, and an Xmon with flux_port as the tunable-coupler transmon in place of TunableCoupler02.

Components

instance

catalog ref

key params

at (x, y)

rot

notes

Q1

Xmon(claws=["w","e"]) (metal:TransmonPocket6)

Metal pad 1000 × 400, pocket 1500 × 1200, pad_gap 50; pads bus_03 (loc_W 0, loc_H −1, w 100, gap 50), readout (0, +1, 100, 50); orientation 90

(4000, 2000)

0

Metal pins: bus_03 E (4700, 2000) → coupler; readout W (3300, 2000) → P1

Q2

Xmon(claws=["w","e"])

same

(12000, 2000)

0

Metal: bus_03 E (12700, 2000) → P2; readout W (11300, 2000) → coupler

TC

Xmon(claws=["w","e"], flux_port=True, cross_length=300) (metal:TunableCoupler02)

Metal: pad_radius 300, bus_width 100, bus inner/outer 500, JJ 100 × 400, fbl 100 × 500, fbl_offset 100

(8000, 2000)

180

flux points N after rot 180; Metal pins pin2 (6100, 2050) W, pin1 (9900, 2050) E, fbl (7550, 3000) N

P1_C

BondPad(pad_width=500, pad_height=1000)

lead 0

(1000, 2500)

0

P2_C

BondPad

same

(15000, 2500)

0

P3_C

BondPad

same

(11000, 5000)

90

Metal orientation −180, faces W

Routes

route

from → to

type, length

waypoints

notes

route1

Q1.claw_e → TC.claw_e (faces W after rot 180)

cpw ≈ 1400

—

Metal RouteStraight Q1.bus_03 → TC.pin2

route2

Q2.claw_w → TC.claw_w (faces E)

cpw ≈ 1400

—

Metal Q2.readout → TC.pin1 (pin names swapped in the source)

route3

P3_C.a → TC.flux

cpw ≈ 5320 (Metal)

[(x_flux, 5000)], x_flux ≈ 8010 = TC.flux x

Metal: W 3.4 mm to (7600, 5000), then down to fbl (7550, 3000); fillet 90

route4

Q1.claw_w → P1_C.a

meander 10 000

—

lead 200/500, fillet 90, asym 0

route5

Q2.claw_e → P2_C.a

meander 10 000

—

same

Launchers, pads, test structures, markers, labels

3 pads: P1 and P2 are the qubit lines (bottom edge) and P3 is the coupler flux bias (top). There are no markers.

LOM node structure

  • Q1 and Q2 are fixed transmons, each a two-pad island pair with a JJ (Xmon: island + JJ to ground).

  • TC is a flux-tunable coupler: an island with a SQUID (TrilayerSquid / junction list) and the flux bias from P3.

  • The coupling chain is Q1, C_g, TC, C_g, Q2.

  • Each qubit has a 10 mm line to a 50 Ω port. It is a direct port line, not a resonator: the pads end galvanically on wire-bond pads.

Targets (if stated)

None.

Simplifications for a first rebuild

  1. Scale the qubits down to the Xmon default size (cross_length 300). Keep the 4 mm qubit–coupler spacing, or shorten it to ≈1 mm with the routes as straight cpw.

  2. The Metal “readout” lines are not resonators. To read out, replace route4 and route5 with λ/4 meanders hanging off a feedline (as in A2_two_coupled).

  3. Put a SQUID on TC: junction={"Lj_nH": [Lj1, Lj2]} or junction_type for the SQUID.

Quantcore PDK rebuild

The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore’s.

Notebook: examples/designs/metal/iswap2_pocket_tc.ipynb.

  • Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), drawn on the source’s 16 × 6 mm chip (the design does not fit the 7.5 mm die); no KQC chip frame.

  • Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); Metal’s DesignPlanar default is silicon (εr 11.45, 750 µm), so the LOM capacitances, resonator frequencies and FEM jobs here are for sapphire rather than the source’s substrate.

  • Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (junction_type from layouts.registry.trilayer_junction): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed); both qubits get the PDK nominal junction, 0.5 × 0.6 µm fingers → R_n = 45 kΩ, L_J = 6.73 nH, C_J = 15 fF (in the 40–50 kΩ window), the coupler (TunableCoupler02, a series SQUID) a PDK SQUID of two 0.25 × 0.6 µm junctions → R_n = 45 kΩ in parallel, L_J = 6.73 nH at zero flux, C_J = 15 fF (in the 40–50 kΩ window), in place of the assumed 10 nH + 2 fF. Expected f_q ≈ 4.3 GHz (an estimate for the mm-scale pads), the coupler ≈ 5.3 GHz at zero flux. The two qubits stay identical.

  • Kept: the topology and every Metal component with the source’s options (through the metal: wrapper), positions and orientations, every route’s end pins and total length, the sim groups (including the coupler pocket, which the rebuild adds).