SpiralLine

Spiral line by angle (legacy draw.spiral): Archimedean, Fermat or double Fermat; ports a / b.

Source: Quantcore. Category: resonator. Module: quantcore_circuits.layouts.others.spirals.

See also the catalog.

Pins

Pins of SpiralLine

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

a

-61.399

0

268.17

2

6

CPW end; LOM node line

b

61.399

0

88.17

2

6

CPW end; LOM node line

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: legacy draw.spiral (Archimedean / Fermat / double Fermat by angle; the legacy double-Fermat typo y_bls/y1s fixed). Ports ‘a’/’b’ at the path ends face along the tangent (not Manhattan); metal by default: place it on a pocket (pocket_margin, or metal:Rectangle subtract). LOM: an open-ended line of the drawn length (rough, no kinetic inductance).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

start_angle

0.0

rad

Start angle

end_angle

37.69911184307752

rad

End angle (6 turns = 12π)

width

2

μm

Line width (legacy w)

spiral_type

"double_fermat"

–

Spiral

spiral_r

10

μm

Spiral scale (Archimedean: r = spiral_r·φ; Fermat: r = spiral_r·√φ)

points

1000

–

Points (legacy npoints; per arm for the double Fermat)

metal

true

–

Metal line (base_metal_addition); False: etched (legacy 1/0)

pocket_margin

0

μm

Own square pocket beyond the spiral (0 = none)

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

  • no lumped branches

line

node

length (µm)

a (µm)

b (µm)

ends

X

line

3102.706

2

3.117

open / open

Nodes: line.

  • X: spiral line 3103 µm (gap = mean turn spacing 3.1 µm; rough; kinetic L as a CPW)

Simulation export notes

  • C6: eigenmode 50 Ω edge port without a polygon (box edge on a bend / taper / narrow line) (status: fixed; fix in sim_tools/builder.py (straighten_box, edge_port_ok, crossing_square))

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "SpiralLine", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.a")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components SpiralLine lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.

GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect made, build refused (routing error shown; Undo), build ok. ports are 2 um CPW and 1.8 deg off-axis: a Connect to a 10/6 BondPad cannot route (error shown, Undo).