metal:TransmonConcentricType2

TransmonConcentricType2.png

Source: Metal (Qiskit Metal). Category: qubit. Module: qiskit_metal.qlibrary.qubits.transmon_concentric_type_2.

See also the catalog.

Pins

Pins of metal:TransmonConcentricType2

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

pin1

1909.19

1909.187

45

10

6

LOM node pin1

pin2

-1909.19

1909.187

135

10

6

LOM node pin2

pin3

-1909.19

-1909.187

225

10

6

LOM node pin3

squid_a

707.107

-707.106

none

10

6

junction pins (the LOM’s L_J); LOM node island1

squid_b

1060.661

-1060.659

none

10

6

junction pins (the LOM’s L_J); LOM node island2

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: draws metal only, no pocket (Metal leaves its pocket commented out): alone it is empty in the negative mask, as in Metal’s own GDS (metal on the ground plane). Place it on a pocket, e.g. metal:Rectangle with subtract: true; its metal goes to base_metal_addition, which the fab export removes from the etch. Metal’s defaults are mm-scale.

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

junction_type

"Metal"

–

Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line

junction_params

"{}"

–

Trilayer junction cell parameters (JSON dict, e.g. lj_nH)

metal_class

"TransmonConcentricType2"

–

Quantum Metal component

options

"{}"

–

Metal options as JSON (bare numbers on length options are µm)

open_pins

""

–

Pins left open (comma-separated): keep Metal’s etch beyond them, as drawn with no route attached

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X_1

C

island1 – gnd

estimate=590, unit=fF, estimate_source=rough: ring, estimate_kind=rough, uncertainty=±50%

C_X_2

C

island2 – gnd

estimate=82, unit=fF, estimate_source=rough: disk to ground, screened by the ring, estimate_kind=rough, uncertainty=±50%

C_X_12

C

island1 – island2

estimate=740, unit=fF, estimate_source=rough: disk–ring facing edges (CPS), estimate_kind=rough, uncertainty=±50%

J_X

SQUID

island1 – island2

Lj_nH=–, Cj_fF=0, asym=0, flux_phi0=0

Cg_X_pin1

C

island1 – pin1

estimate=46, unit=fF, estimate_source=rough: NE finger along the ring (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin1

C

pin1 – gnd

estimate=64, unit=fF, estimate_source=rough: finger as CPW, estimate_kind=rough, uncertainty=±50%

Cg_X_pin2

C

island1 – pin2

estimate=46, unit=fF, estimate_source=rough: NW finger along the ring (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin2

C

pin2 – gnd

estimate=64, unit=fF, estimate_source=rough: finger as CPW, estimate_kind=rough, uncertainty=±50%

Cg_X_pin3

C

island1 – pin3

estimate=46, unit=fF, estimate_source=rough: SW finger along the ring (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin3

C

pin3 – gnd

estimate=64, unit=fF, estimate_source=rough: finger as CPW, estimate_kind=rough, uncertainty=±50%

Nodes: island1, island2, pin1, pin2, pin3.

Simulation export notes

  • C5b: metal-only Metal cell placed without its pocket (status: context; fix in — (design side))

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "metal:TransmonConcentricType2", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.pin1")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components metal:TransmonConcentricType2 lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.