CoupledConnector¶
Meandered CPW connector from the origin downwards (legacy Coupled Connector); ports start, end.
Source: Quantcore. Category: waveguide. Module: quantcore_circuits.layouts.others.legacy_resonators.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
-1545.916 |
270 |
10 |
6 |
far end of the line / resonator (see the notes); LOM node |
|
0 |
0 |
90 |
10 |
6 |
LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Notes from the catalog: ‘end’ is an open end with ground=False (default): the gap box covers the port, so nothing can be joined galvanically; ground=True leaves the end for a connection.
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Meander width (straight run between arcs) |
|
|
μm |
Arc length of a meander turn (radius = arc_length / π) |
|
|
μm |
Neck length |
|
|
μm |
Coupling gap (ground strip around the shorted end) |
|
|
μm |
Coupling length (subtracted from the meander length) |
|
|
– |
End left without a gap cap, for a connection |
|
|
μm |
Length of the resonator |
|
|
– |
Points per arc (legacy n) |
|
|
– |
Flip the meander direction |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
no lumped branches
line |
node |
length (µm) |
a (µm) |
b (µm) |
ends |
|---|---|---|---|---|---|
|
|
3899.992 |
10 |
6 |
short / open |
Nodes: line.
Simulation export notes¶
C8: GDS polygon with > 4095 points (XY record > 0x8000 bytes) (status: partly fixed; fix in sim_tools/builder.py (FaceMetal.max_points, DesignSimulation.simplified_region, split_large_polygons); sim_tools/geometry_check.py)
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "CoupledConnector", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.end") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components CoupledConnector lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok.