CpwTsvTransition

CPW transition through one chip: a pad on each face, joined by signal TSVs, with ground TSVs around them.

Source: Quantcore. Category: flip_chip. Module: quantcore_circuits.layouts.others.flip_chip.

See also the catalog.

Pins

Pins of CpwTsvTransition

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

a

-115

0

180

10

6

CPW end; LOM node line

b

115

0

0

10

6

CPW end; LOM node line

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: port ‘a’ is on face_ids[0] (the front pad), ‘b’ on the other side of the same chip (1t1 → 1b1, 2b1 → 2t1); a route to either is drawn on that port’s face. Set face_ids=[‘2b1’] for a TSV through the top chip. LOM: one conductor (tapers + pad length; the via height is not modelled).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

taper_length

100

μm

Front taper length (0: port at the pad)

taper_length_back

100

μm

Back taper length (0: port at the pad)

pad_width

40

μm

Pad centre-conductor width

pad_gap

24

μm

Pad gap to ground (also closes the pad)

pad_length

30

μm

Pad length along the line

n_ground_vias_per_side

4

–

Ground TSVs on each side of the pad

ground_via_pitch

30

μm

Ground TSV pitch along the line

ground_via_distance

15

μm

Ground TSV centres from the pad gap’s outer edge

tsv_elliptical_width

20

μm

TSV elliptical width

n_signal_vias

2

–

Signal TSVs in the pad

signal_via_pitch

20

μm

Signal TSV pitch across the line

tsv_type

"Tsv Ellipse"

–

TSV type

tsv_diameter

10

μm

TSV diameter

tsv_margin

30

μm

TSV margin

a2

-1

μm

Width of center conductor on the other end

b2

-1

μm

Width of gap on the other end

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

  • no lumped branches

line

node

length (µm)

a (µm)

b (µm)

ends

X

line

230

10

6

short / short

Nodes: line.

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "CpwTsvTransition", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.a")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components CpwTsvTransition lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.

GUI status: not listed in kplugin/COMPONENTS_STATUS.md.