FingerCapacitorSquare¶
The PCell declaration for a square finger capacitor.
Source: KQC (KQCircuits). Category: capacitor. Module: kqcircuits.elements.finger_capacitor_square.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-36.5 |
0 |
180 |
10 |
6 |
CPW end; LOM node |
|
36.5 |
0 |
0 |
10 |
6 |
CPW end; LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Gap between the finger and other pad |
|
|
μm |
Ground plane padding |
|
|
μm |
Fixed length of element, 0 for auto-length |
|
|
μm |
Ground connection width per gap ratio |
|
|
– |
Number of fingers |
|
|
μm |
Width of a finger |
|
|
μm |
Gap between the fingers |
|
|
μm |
Length of the fingers |
|
|
μm |
Width of center conductor on the other end |
|
|
μm |
Width of gap on the other end |
|
|
μm |
Corner radius |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
a – b |
estimate=7.18, unit=fF, estimate_source=analytic: interdigital (Igreja & Dias 2004) + finger-tip gaps, estimate_kind=analytic, uncertainty=±25% |
|
C |
a – gnd |
estimate=3.5, unit=fF, estimate_source=rough: half the finger area as a pad in the ground padding, estimate_kind=rough, uncertainty=±50% |
|
C |
b – gnd |
estimate=3.5, unit=fF, estimate_source=rough: half the finger area as a pad in the ground padding, estimate_kind=rough, uncertainty=±50% |
Nodes: a, b.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "FingerCapacitorSquare", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components FingerCapacitorSquare lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.