metal:TransmonPocket6¶
Transmon pocket with 6 connection pads.
Source: Metal (Qiskit Metal). Category: qubit. Module: qiskit_metal.qlibrary.qubits.transmon_pocket_6.
Note
Alias of metal:TransmonPocket: the same circuit, drawn differently. same options; for the same connection pad set Pocket6’s pad_cpw_shift 5 µm and pocket_rise 65 µm (TransmonPocket’s pad defaults; Pocket6’s own are 0) (XOR 0); loc_W 0 adds Pocket6’s middle positions
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
-15 |
none |
10 |
6 |
junction pins (the LOM’s L_J); LOM node |
|
0 |
15 |
none |
10 |
6 |
junction pins (the LOM’s L_J); LOM node |
Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line |
|
|
– |
Trilayer junction cell parameters (JSON dict, e.g. lj_nH) |
|
|
– |
Quantum Metal component |
|
|
– |
Metal options as JSON (bare numbers on length options are µm) |
|
|
– |
Pins left open (comma-separated): keep Metal’s etch beyond them, as drawn with no route attached |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island1 – gnd |
estimate=36, unit=fF, estimate_source=analytic: coupled pads in a pocket (analytic) × Q3D anchor^1.00 (Metal tutorial Q3D, TransmonPocket defaults (Q1_TwoTransmon_CapMatrix)), estimate_kind=analytic, uncertainty=±25% |
|
C |
island2 – gnd |
estimate=36, unit=fF, estimate_source=analytic: coupled pads in a pocket (analytic) × Q3D anchor^1.00 (Metal tutorial Q3D, TransmonPocket defaults (Q1_TwoTransmon_CapMatrix)), estimate_kind=analytic, uncertainty=±25% |
|
C |
island1 – island2 |
estimate=27.7, unit=fF, estimate_source=analytic: coupled pads in a pocket (analytic) × Q3D anchor^1.00 (Metal tutorial Q3D, TransmonPocket defaults (Q1_TwoTransmon_CapMatrix)), estimate_kind=analytic, uncertainty=±25% |
|
JJ |
island1 – island2 |
Lj_nH=10, Cj_fF=0 |
Nodes: island1, island2.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "metal:TransmonPocket6", at=(3750, 3750), a=10) # parameters: see the table above
# no directed pin: place it with at= / rot=, or snap it with snap= / to=
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components metal:TransmonPocket6 lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.