QuarterWaveCpwResonator¶
CPW Resonator
Source: KQC (KQCircuits). Category: resonator. Module: kqcircuits.elements.quarter_wave_cpw_resonator.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-250 |
0 |
180 |
10 |
6 |
CPW end; LOM node |
|
250 |
0 |
0 |
10 |
6 |
CPW end; LOM node |
|
0 |
-1076 |
270 |
10 |
10 |
LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Probeline length |
|
|
μm |
Resonator length |
|
|
– |
Resonator termination type |
|
|
– |
Number of fingers |
|
|
– |
Finger length |
|
|
– |
Include ground-grid in the trace |
|
|
– |
Capacitor coupler type |
|
|
– |
Internal ports (EPR) |
|
|
μm |
Maximal straight length of resonators |
|
|
– |
Resonator beginning type |
|
|
– |
Number of resonator airbridges |
|
|
– |
Airbridge type |
|
|
– |
Airbridges on transmission line |
|
|
μm |
Trace width of resonator line |
|
|
μm |
Gap width of resonator line |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
pl – res |
estimate=6.4, unit=fF, estimate_source=rough: SmoothCapacitor electrode gap (CPS), estimate_kind=rough, uncertainty=±50% |
line |
node |
length (µm) |
a (µm) |
b (µm) |
ends |
|---|---|---|---|---|---|
|
|
1000 |
10 |
10 |
open / short |
Nodes: pl, res.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "QuarterWaveCpwResonator", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components QuarterWaveCpwResonator lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.