LumpedJpa

Lumped JPA: a trilayer junction or SQUID to ground, shunted by an interdigital capacitor (twpa-sim jpa /

Source: Quantcore. Category: resonator. Module: quantcore_circuits.layouts.others.amplifiers.

See also the catalog.

Pins

Pins of LumpedJpa

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

signal

0

0

180

10

6

signal line end; LOM node island

squid_a

390

0

none

10

6

junction pins (the LOM’s L_J)

squid_b

406

0

none

10

6

junction pins (the LOM’s L_J)

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

coupling

"capacitive"

–

Coupling to the signal line

junction_type

"Quantcore Junction"

–

Junction (trilayer cell)

junction_params

"{}"

–

Trilayer junction cell parameters (JSON dict)

lead_length

50

μm

CPW lead from the port to the pocket

spine_width

20

μm

Island spine width

shunt_fingers

20

–

Island fingers per side

finger_length

100

μm

Finger length

finger_width

4

μm

Finger width

finger_gap

4

μm

Gap between fingers (and all island clearances)

junction_gap

16

μm

Junction gap (window height)

tap_width

4

μm

Inductive coupling strip width

tap_pad

[20, 24]

–

Inductive coupling tap pad (length along x, width), µm

flux_length

200

μm

Flux line length (port to short)

flux_gap

2

μm

Ground strip between the pocket and the flux line gap

flux_line

false

–

Draw a shorted flux / pump line past the junction (capacitive)

flux_offset

20

μm

Flux short beyond the junction axis

flux_phi0

0.0

Φ0

Static flux bias of a SQUID (LOM)

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X

C

island – gnd

estimate=392, unit=fF, estimate_source=analytic: 2 × IDC (41 fingers 4/4 µm, overlap 96 µm, Igreja–Dias) + spine ends, estimate_kind=analytic, uncertainty=±25%

J_X

JJ

island – gnd

Lj_nH=6.734, Cj_fF=15

Nodes: island.

  • X: lumped JPA, C_shunt ≈ 392 fF (analytic IDC)

Simulation export notes

  • C4: galvanic lead port shorted to ground / leaving the box (status: fixed; fix in sim_tools/builder.py (lead_open_ends, galvanic_routes, build_simulation))

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "LumpedJpa", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.signal")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components LumpedJpa lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.

GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).