Flipmon

Circular flip-chip transmon (QPDK flipmon_with_bbox), optionally with its plate readout coupler.

Source: Quantcore. Category: qubit. Module: quantcore_circuits.layouts.qubits.qpdk_cells.

See also the catalog.

Pins

Pins of Flipmon

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

coupler

170

0

0

10

6

coupler port (readout / bus); LOM node cplr

squid_a

60

0

none

10

6

junction pins (the LOM’s L_J); LOM node island2

squid_b

80

0

none

10

6

junction pins (the LOM’s L_J); LOM node island1

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: QPDK flipmon_with_bbox (MIT). Face 2b1 (top-chip disc, its etch, the bump) is on KQC face-2b1 layers, which the PDK maps to 800/0+ (flip-chip). Port ‘coupler’ is on the M1 etch edge, 13 µm beyond QPDK’s plate port o1 at defaults.

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

mirror_squid

false

–

Mirror SQUID by its Y axis

junction_type

"Manhattan"

–

Junction Type

junction_width

0.02

μm

Junction width for code generated element

inner_circle_radius

60

μm

Inner disc radius (M1)

outer_ring_radius

110

μm

Outer ring centre radius (M1)

outer_ring_width

60

μm

Outer ring width (M1)

top_circle_radius

110

μm

Top disc radius (M2, face 1)

m1_etch_extension_gap

30

μm

M1 etch radius beyond the ring

m2_etch_extension_gap

40

μm

M2 etch radius beyond the top disc

junction_position_rotation

0

°

Junction angle around the centre

junction_params

"{}"

–

Junction cell parameters (JSON dict)

with_coupler

true

–

Draw the plate readout coupler and its port

coupler_width

10

μm

Coupler plate radial width

coupler_length

58

μm

Coupler plate length (tangential)

coupler_offset

10

μm

Coupler plate centre beyond the ring’s outer edge

coupler_etch_margin

2

μm

Etch margin around the plate

loop_area

100

μm^2

Loop area

fluxline_type

"Fluxline Standard"

–

Fluxline Type

bump_diameter

15

μm

Indium bump diameter

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X_1

C

island1 – gnd

estimate=83.3, unit=fF, estimate_source=analytic: ring 80–140 µm, outer edge as half CPW (30 µm gap), estimate_kind=analytic, uncertainty=±25%

C_X_12

C

island1 – island2

estimate=46, unit=fF, estimate_source=rough: disc–ring facing edges as coplanar strips along the mean circumference, estimate_kind=rough, uncertainty=±50%

C_X_2

C

island2 – gnd

estimate=5.1, unit=fF, estimate_source=rough: M1 disc to ground screened by the ring, estimate_kind=rough, uncertainty=±50%

C_X_12_flip

C

island1 – island2

estimate=20, unit=fF, estimate_source=rough: M2 disc r 110 over the M1 ring: parallel plate, 17907 µm² across an assumed 8 µm vacuum gap, estimate_kind=rough, uncertainty=±50%

C_X_2_top

C

island2 – gnd

estimate=71, unit=fF, estimate_source=rough: M2 disc r 110 in its 40 µm top-face gap (single-face formula), estimate_kind=rough, uncertainty=±50%

J_X

SQUID

island1 – island2

Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0

Cg_X_cplr

C

island1 – cplr

estimate=6.43, unit=fF, estimate_source=analytic: plate 58×10 µm facing the ring across 5 µm (CPS), estimate_kind=analytic, uncertainty=±25%

Cc_X_cplr

C

cplr – gnd

estimate=7.4, unit=fF, estimate_source=rough: plate in the M1 etch + its lead, estimate_kind=rough, uncertainty=±50%

Nodes: island1, island2, cplr.

  • X: M2 top disc (face 2b1) counted in island2 across an assumed 8 µm flip-chip gap (rough; PDK v2 does not fabricate face 2b1); coupler ↔ disc C neglected (screened by the ring)

Simulation export notes

  • C1: Sim junction pads overlap / end on a curved island in a narrow gap (status: fixed; fix in layouts/junctions/sim_gap.py; layouts/qubits/qpdk_cells.py; layouts/qubits/sqdmetal_cells.py)

  • C2: indium bump in a one-face simulation is a PEC pillar to the top of the box (status: fixed; fix in sim_tools/builder.py)

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "Flipmon", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.coupler")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components Flipmon lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.

GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).